Nickel alloy, titanium and stainless strip and sheet — coils or cut lengths

Supply range

Thickness	0.05 – 4.76 mm
Form	Coils or cut lengths; slit to width
Finish	Pickled or bright; 8K mirror finish available

Sizes and conditions outside the standards can be supplied by agreement; please confirm on enquiry.

Types

Cold-rolled strip

Narrower widths, usually supplied in coils.

Sheet

Wider widths, usually supplied in cut lengths.

Foil

Very thin strip for bellows, seals and electronic parts.

Thickness, width and length tolerances

Units

Permitted variations in thickness, width and length when ordered to the standard. If you need closer tolerances, state them in your enquiry.

ASTM B127, B162, B168, B409, B424, B443Nickel alloy sheet and stripThickness ±0.038 – 0.56 mm±0.0015 – 0.022 in

Measured at least 9.5 mm (⅜ in) from any edge; strip under 25.4 mm (1 in) wide may be measured anywhere. Strip over 3.2 mm (0.125 in) thick, and strip over 305 mm (12 in) wide, takes the sheet tolerances.

Sheet, thickness tolerance (±)

Thickness mmin	Hot-rolled sheet, width mmin		Cold-rolled sheet, width mmin
Thickness mmin	≤ 1220≤ 48	> 1220 – 1520> 48 – 60	≤ 1220≤ 48	> 1220 – 1520> 48 – 60
0.5 – 0.60.018 – 0.025	0.080.003	0.100.004	0.050.002	0.080.003
> 0.6 – 0.9> 0.025 – 0.034	0.100.004	0.130.005	0.080.003	0.100.004
> 0.9 – 1.1> 0.034 – 0.043	0.130.005	0.150.006	0.100.004	0.130.005
> 1.1 – 1.4> 0.043 – 0.056	0.130.005	0.150.006	0.100.004	0.130.005
> 1.4 – 1.8> 0.056 – 0.070	0.150.006	0.180.007	0.130.005	0.150.006
> 1.8 – 1.9> 0.070 – 0.078	0.180.007	0.200.008	0.150.006	0.180.007
> 1.9 – 2.4> 0.078 – 0.093	0.200.008	0.230.009	0.180.007	0.200.008
> 2.4 – 2.8> 0.093 – 0.109	0.230.009	0.250.010	0.180.007	0.230.009
> 2.8 – 3.2> 0.109 – 0.125	0.250.010	0.310.012	0.200.008	0.250.010
> 3.2 – 3.6> 0.125 – 0.140	0.310.012	0.360.014	0.200.008	0.250.010
> 3.6 – 4.3> 0.140 – 0.171	0.360.014	0.410.016	0.230.009	0.310.012
> 4.3 – 4.8> 0.171 – 0.187	0.380.015	0.430.017	0.250.010	0.330.013
> 4.8 – 5.5> 0.187 – 0.218	0.430.017	0.480.019	0.280.011	0.380.015
> 5.5 – 5.9> 0.218 – 0.234	0.460.018	0.510.020	0.310.012	0.410.016
> 5.9 – 6.4> 0.234 – 0.250	0.510.020	0.560.022	0.330.013	0.460.018

Cold-rolled strip up to 305 mm (12 in) wide

Thickness mmin	Tolerance (±) mmin
≤ 1.27≤ 0.050	0.0380.0015
> 1.27 – 2.39> 0.050 – 0.093	0.0630.0025
> 2.39 – 3.18> 0.093 – 0.125	0.110.004

Width

Width tolerance of strip; sheet (up to 6.35 mm thick) is +3.18 / 0 mm (+0.125 / 0 in) at all widths

Thickness mmin	Width mmin
Thickness mmin	≤ 305≤ 12	> 305 – 1219> 12 – 48
< 1.9< 0.075	±0.18±0.007	+1.6 / 0+0.062 / 0
1.9 – 2.50.075 – 0.100	±0.23±0.009	+1.6 / 0+0.062 / 0
> 2.5 – 3.2> 0.100 – 0.125	±0.30±0.012	+1.6 / 0+0.062 / 0
> 3.2 – 4.1> 0.125 – 0.160	±0.41±0.016	+1.6 / 0+0.062 / 0
> 4.1 – 4.7> 0.160 – 0.187	±0.51±0.020	+1.6 / 0+0.062 / 0
> 4.7 – 6.4> 0.187 – 0.250	±1.6±0.062	±1.6±0.062

ASTM B333, B435, B575, B582Nickel alloy sheet and stripPlus thickness 0.10 – 0.46 mm0.004 – 0.018 inMinus thickness 0.10 – 0.25 mm0.004 – 0.010 in

Strip of all widths and sheet up to 1220 mm (48 in) wide; measured at least 9.5 mm (⅜ in) from any edge. Light surface imperfections may be buffed out to a depth within the minus tolerance.

Thickness mmin	Plus mmin	Minus mmin
0.51 – 0.860.020 – 0.034	0.100.004	0.100.004
> 0.86 – 1.42> 0.034 – 0.056	0.130.005	0.130.005
> 1.42 – 1.78> 0.056 – 0.070	0.150.006	0.150.006
> 1.78 – 1.98> 0.070 – 0.078	0.180.007	0.180.007
> 1.98 – 2.36> 0.078 – 0.093	0.200.008	0.200.008
> 2.36 – 2.77> 0.093 – 0.109	0.230.009	0.230.009
> 2.77 – 3.18> 0.109 – 0.125	0.250.010	0.250.010
> 3.18 – 3.56> 0.125 – 0.140	0.330.013	0.250.010
> 3.56 – 4.34> 0.140 – 0.171	0.410.016	0.250.010
> 4.34 – 4.75> 0.171 – 0.187	0.460.018	0.250.010

Width

Thickness mmin	Width mmin	Tolerance mmin
Sheet
≤ 4.76≤ 0.187	≥ 50.8≥ 2	+3.18 / 0+0.125 / 0
Strip (slit edges)
> 0.51 – 1.90> 0.020 – 0.075	≤ 610≤ 24	±0.18±0.007
> 1.90 – 2.54> 0.075 – 0.100	≤ 610≤ 24	±0.23±0.009
> 2.54 – 3.18> 0.100 – 0.125	≤ 610≤ 24	±0.30±0.012

ASTM B625, B688, B463, B709Super-austenitic stainless and iron-nickel alloy sheet and stripThickness ±0.03 – 0.36 mm±0.001 – 0.014 in

State the edge (No. 1, 3 or 5) when ordering strip; width tolerances depend on it. Material ordered to A240 follows the stainless group below.

Hot-rolled sheet in cut lengths; cold-rolled sheet in cut lengths and coils

Thickness mmin	Tolerance (±) mmin
0.130.005	0.030.001
> 0.13 – 0.18> 0.005 – 0.007	0.040.0015
> 0.18 – 0.41> 0.007 – 0.016	0.050.002
> 0.41 – 0.66> 0.016 – 0.026	0.080.003
> 0.66 – 1.02> 0.026 – 0.040	0.100.004
> 1.02 – 1.47> 0.040 – 0.058	0.130.005
> 1.47 – 1.83> 0.058 – 0.072	0.150.006
> 1.83 – 2.11> 0.072 – 0.083	0.180.007
> 2.11 – 2.49> 0.083 – 0.098	0.200.008
> 2.49 – 2.90> 0.098 – 0.114	0.230.009
> 2.90 – 3.30> 0.114 – 0.130	0.250.010
> 3.30 – 3.68> 0.130 – 0.145	0.300.012
> 3.68 – < 4.76> 0.145 – < 3/16	0.360.014

Cold-rolled strip in coils and cut lengths, crown included

Thickness mmin	Width; tolerance (±) mmin
Thickness mmin	4.76 – 1523/16 – 6	> 152 – 305> 6 – 12	> 305 – < 610> 12 – < 24
0.13 – 0.250.005 – 0.010	10 %	10 %	10 %
> 0.25 – 0.28> 0.010 – 0.011	0.040.0015	0.040.0015	0.040.0015
> 0.28 – 0.33> 0.011 – 0.013	0.040.0015	0.040.0015	0.050.002
> 0.33 – 0.43> 0.013 – 0.017	0.040.0015	0.050.002	0.050.002
> 0.43 – 0.51> 0.017 – 0.020	0.040.0015	0.050.002	0.060.0025
> 0.51 – 0.74> 0.020 – 0.029	0.050.002	0.060.0025	0.060.0025
> 0.74 – 0.89> 0.029 – 0.035	0.050.002	0.080.003	0.080.003
> 0.89 – 1.27> 0.035 – 0.050	0.060.0025	0.090.0035	0.090.0035
> 1.27 – 1.75> 0.050 – 0.069	0.080.003	0.090.0035	0.090.0035
> 1.75 – 2.54> 0.069 – 0.100	0.080.003	0.100.004	0.130.005
> 2.54 – 2.98> 0.100 – 0.125	0.100.004	0.110.0045	0.130.005
> 2.98 – 4.09> 0.125 – 0.161	0.110.0045	0.110.0045	0.130.005
> 4.09 – < 4.76> 0.161 – < 3/16	0.130.005	0.130.005	0.150.006

Strip width; sheet width, length and flatness

Cold-rolled strip width (±), No. 3 edge

Thickness mmin	Width mmin
Thickness mmin	4.76 – < 12.703/16 – < 1/2	12.70 – 152.401/2 – 6	> 152.40 – 228.60> 6 – 9	> 228.60 – 304.80> 9 – 12	> 304.80 – 508.00> 12 – 20	> 508.00 – 609.60> 20 – 24
≤ 1.73≤ 0.068	0.130.005	0.130.005	0.130.005	0.250.010	0.410.016	0.510.020
1.75 – 2.510.069 – 0.099	0.200.008	0.200.008	0.250.010	0.250.010	0.410.016	0.510.020
2.54 – 4.060.100 – 0.160	0.250.010	0.250.010	0.410.016	0.410.016	0.510.020	0.510.020
4.09 – < 4.760.161 – < 3/16	—	0.410.016	0.510.020	0.510.020	0.790.031	0.790.031

Cold-rolled strip width (±), No. 1 and No. 5 edges

Edge	Width mmin	Thickness mmin	Tolerance (±) mmin
1, 5	≤ 7.14≤ 9/32	≤ 1.59≤ 1/16	0.130.005
1, 5	> 7.14 – 19.05> 9/32 – 3/4	≤ 2.38≤ 3/32	0.130.005
1, 5	> 19.05 – 127> 3/4 – 5	≤ 3.18≤ 1/8	0.130.005
5	> 127.00 – 228.60> 5 – 9	0.20 – 3.180.008 – 1/8	0.250.010
5	> 228.60 – 508.00> 9 – 20	0.38 – 2.670.015 – 0.105	0.250.010
5	> 508.00> 20	0.58 – 2.030.023 – 0.080	0.380.015

Resquared (stretcher-levelled) sheet: under 3.33 mm (0.131 in) thick, +1.59 mm (1/16 in) under 1219 mm (48 in) wide and +3.18 mm (⅛ in) at 1219 mm and over, +1.59 mm under 3048 mm (120 in) long and +3.18 mm at 3048 mm and over; 3.33 mm and thicker, +6.35 mm (¼ in) on all widths and lengths; no minus tolerance.
Sheet not resquared and cold-rolled coil (under 4.76 mm thick): width +1.59 mm from 610 to under 1219 mm (24 – 48 in), +3.18 mm at 1219 mm and over; length +6.35 mm up to 3048 mm (10 ft), +12.70 mm to 6096 mm (20 ft); no minus tolerance.
Flatness of stretcher-levelled sheet (under 4.76 mm thick): 3.18 mm up to 1219 mm wide and 2438 mm (96 in) long, 6.35 mm otherwise.
Camber in any 2438 mm (8 ft): sheet not resquared and cold-rolled coil, 3.18 mm for 610 – 914 mm wide and 2.38 mm over 914 mm; cold-rolled strip, 12.70 mm up to 38.10 mm wide and 6.35 mm from 38.10 to 609.60 mm.

ASTM A240Stainless steel strip and sheetCold-rolled strip ±0.010 – 0.090 mm±0.0006 – 0.006 inCold-rolled sheet ±0.03 – 0.25 mm±0.001 – 0.010 in

Under 600 mm (24 in) wide is narrow (strip), wider is wide (sheet and coil). Material ordered in mm follows the metric table and material ordered in inches the inch table; the two are banded differently. For a thickness not shown, use the next greater thickness.

Cold-rolled narrow product (strip), crown included

Thickness mm	Width; tolerance (±) mm
Thickness mm	≤ 125	> 125 – 250	> 250 – < 600
0.15	0.010	0.015	0.020
0.25	0.015	0.020	0.025
0.50	0.025	0.030	0.035
0.75	0.030	0.040	0.050
1.00	0.030	0.040	0.050
1.25	0.035	0.045	0.050
1.50	0.040	0.050	0.060
1.75	0.050	0.060	0.070
2.00	0.050	0.060	0.070
2.50	0.050	0.070	0.080
3.00	0.060	0.070	0.090
4.00	0.070	0.070	0.090
4.99	0.070	0.070	0.090

Cold-rolled narrow product (strip), crown included

Thickness in	Width; tolerance (±) in
Thickness in	≤ 6	> 6 – 12	> 12 – 24
0.002 – < 0.005	10 %	10 %	10 %
0.005 – 0.010	0.0006	0.0008	0.001
> 0.010 – 0.012	0.001	0.001	0.001
> 0.012 – 0.015	0.001	0.0015	0.0015
> 0.015 – 0.020	0.001	0.0015	0.0015
> 0.020 – 0.029	0.0015	0.0015	0.002
> 0.029 – 0.035	0.0015	0.002	0.002
> 0.035 – 0.050	0.0025	0.003	0.003
> 0.050 – 0.069	0.003	0.003	0.003
> 0.069 – 0.100	0.003	0.003	0.004
> 0.100 – 0.125	0.004	0.004	0.005
> 0.125 – 0.161	0.005	0.005	0.005
> 0.161 – < 3/16	0.005	0.005	0.006

Cold-rolled wide product (sheet and coil)

Thickness mm	Width; tolerance (±) mm
Thickness mm	≤ 1000	> 1000 – 1300	> 1300 – 2100
0.30	0.03	—	—
0.40	0.04	0.04	—
0.50	0.045	0.05	—
0.60	0.05	0.05	—
0.80	0.05	0.05	—
1.00	0.055	0.06	0.07
1.20	0.08	0.08	0.08
1.50	0.08	0.08	0.10
2.00	0.10	0.10	0.11
2.50	0.10	0.11	0.13
3.00	0.13	0.13	0.15
4.00	0.17	0.17	0.17
5.00	0.17	0.17	0.19
6.00	0.17	0.20	0.23
8.00	0.17	0.22	0.25

Cold-rolled wide product (sheet and coil)

Thickness in	Width; tolerance (±) in
Thickness in	≤ 40	> 40 – 50	> 50 – 84
0.012	0.001	—	—
0.016	0.0015	0.0015	—
0.020	0.0015	0.0015	—
0.024	0.002	0.002	—
0.032	0.002	0.002	—
0.040	0.0025	0.0025	0.003
0.047	0.003	0.003	0.003
0.059	0.003	0.003	0.004
0.079	0.004	0.004	0.0045
0.098	0.004	0.004	0.005
0.118	0.005	0.005	0.006
0.157	0.007	0.007	0.007
0.197	0.007	0.007	0.0075
0.236	0.007	0.008	0.009
0.3125	0.007	0.009	0.010

Strip width and length

Cold-rolled narrow product width (±), No. 3 edge

Thickness mm	Width mm
Thickness mm	≤ 40	> 40 – 125	> 125 – 250	> 250 – 600
0.25	0.085	0.10	0.125	0.50
0.50	0.10	0.125	0.15	0.50
1.00	0.125	0.125	0.20	0.50
1.50	0.125	0.15	0.25	0.50
2.50	—	0.20	0.30	0.50
3.00	—	0.25	0.30	0.60
4.00	—	0.25	0.40	0.60
4.99	—	0.40	0.50	0.60

Cold-rolled narrow product width (±), No. 3 edge

Thickness in	Width in
Thickness in	≤ 1.60	> 1.60 – 6	> 6 – 12	> 12 – 24
0.010	0.003	0.004	0.005	0.020
0.020	0.005	0.005	0.010	0.020
0.040	0.005	0.005	0.010	0.020
0.060	0.005	0.006	0.010	0.020
0.100	—	0.010	0.016	0.020
0.120	—	0.010	0.016	0.024
0.160	—	0.016	0.016	0.024
0.200	—	0.030	0.030	0.030

Cold-rolled narrow product, cut length

Length mm	Tolerance mm
≤ 1500	+3 / 0
> 1500 – 4000	+5 / 0
> 4000 – 6000	+8 / 0

Cold-rolled narrow product, cut length

Length	Tolerance in
≤ 6 ft	+1/8 / 0
> 6 – 12 ft	+0.2 / 0
> 12 – 20 ft	+0.3 / 0

ASTM B265Titanium and titanium alloy sheet and stripCold-rolled sheet ±0.03 – 0.36 mm±0.001 – 0.014 inStrip ±0.03 – 0.16 mm±0.001 – 0.006 in

Material 610 mm (24 in) wide and over is sheet, narrower is strip. State cold- or hot-rolled when ordering sheet; if not stated, cold-rolled tolerances apply.

Sheet, thickness tolerance (±)

Thickness mmin	Cold-rolled sheet	Hot-rolled sheet, width mmin
Thickness mmin	Cold-rolled sheet	≤ 2134≤ 84	> 2134> 84
0.130.005	0.030.001	—	—
0.15 – 0.180.006 – 0.007	0.040.0015	—	—
0.20 – 0.410.008 – 0.016	0.050.002	—	—
0.43 – 0.660.017 – 0.026	0.080.003	—	—
0.69 – 1.020.027 – 0.040	0.100.004	—	—
1.04 – 1.470.041 – 0.058	0.130.005	—	—
1.50 – 1.830.059 – 0.072	0.150.006	—	—
1.85 – 2.110.073 – 0.083	0.180.007	—	—
2.13 – 2.490.084 – 0.098	0.200.008	—	—
2.51 – 2.900.099 – 0.114	0.230.009	—	—
2.92 – 3.300.115 – 0.130	0.250.010	0.5080.020	—
3.33 – 3.680.131 – 0.145	0.310.012	0.5580.022	0.710.028
3.71 – < 4.760.146 – < 0.1875	0.360.014	0.640.025	0.710.028

Strip, thickness tolerance (±)

Thickness mmin	Width mmin
Thickness mmin	4.76 – < 25.43/16 – < 1	25.4 – < 76.21 – < 3	76.2 – 152.43 – 6	> 152.4 – 228.6> 6 – 9	> 228.6 – 304.8> 9 – 12	> 304.8 – 406.4> 12 – 16	> 406.4 – 508.0> 16 – 20	> 508.0 – 609.6> 20 – 24
0.250.010	0.030.001	0.030.001	0.030.001	0.030.001	—	0.030.001	0.040.0015	0.040.0015
0.280.011	0.030.001	0.030.001	0.030.001	0.030.001	0.030.001	0.040.0015	0.040.0015	0.040.0015
0.300.012	0.030.001	0.030.001	0.030.001	0.030.001	0.030.001	0.040.0015	0.040.0015	0.040.0015
0.33 – 0.410.013 – 0.016	0.030.001	0.030.001	0.030.001	0.040.0015	0.040.0015	0.040.0015	0.050.002	0.050.002
0.43 – 0.480.017 – 0.019	0.030.001	0.030.001	0.030.001	0.040.0015	0.040.0015	0.050.002	0.050.002	0.050.002
0.51 – 0.640.020 – 0.025	0.030.001	0.030.001	0.040.0015	0.050.002	0.050.002	0.050.002	0.060.0025	0.060.0025
0.66 – 0.710.026 – 0.028	0.030.001	0.040.0015	0.040.0015	0.050.002	0.050.002	0.050.002	0.060.0025	0.080.003
0.74 – 0.860.029 – 0.034	0.040.0015	0.040.0015	0.050.002	0.060.0025	0.060.0025	0.060.0025	0.080.003	0.080.003
0.89 – 0.990.035 – 0.039	0.050.002	0.050.002	0.060.0025	0.080.003	0.080.003	0.080.003	0.080.003	0.080.003
1.02 – 1.240.040 – 0.049	0.050.002	0.050.002	0.060.0025	0.080.003	0.080.003	0.080.003	0.100.004	0.100.004
1.27 – 1.730.050 – 0.068	0.050.002	0.050.002	0.080.003	0.080.003	0.080.003	0.080.003	0.100.004	0.100.004
1.75 – 2.510.069 – 0.099	0.050.002	0.050.002	0.080.003	0.080.003	0.080.003	0.100.004	0.100.004	0.100.004
2.54 – 4.060.100 – 0.160	0.050.002	0.050.002	0.080.003	0.100.004	0.100.004	0.100.004	0.130.005	0.130.005
4.09 – < 4.760.161 – < 3/16	0.050.002	0.080.003	0.100.004	0.100.004	0.100.004	0.130.005	0.160.006	0.160.006

Width, length, flatness and weight

Strip width (±), No. 3 edge

Thickness mmin	Width mmin
Thickness mmin	4.76 – < 12.703/16 – < 1/2	12.70 – 152.401/2 – 6	> 152.40 – 228.60> 6 – 9	> 228.60 – 304.80> 9 – 12	> 304.80 – 508.0> 12 – 20	> 508.0 – < 609.6> 20 – < 24
≤ 1.73≤ 0.068	0.130.005	0.130.005	0.130.005	0.250.010	0.410.016	0.510.020
1.75 – 2.510.069 – 0.099	0.200.008	0.200.008	0.250.010	0.250.010	0.410.016	0.510.020
2.54 – 4.060.100 – 0.160	0.250.010	0.250.010	0.410.016	0.410.016	0.510.020	0.510.020
4.09 – < 4.760.161 – < 3/16	—	0.410.016	0.510.020	0.510.020	0.790.031	0.790.031

Strip length

Length	Tolerance mmin
≤ 1524 mm≤ 5 ft	+9.52 / 0+3/8 / 0
> 1524 – 3048 mm> 5 – 10 ft	+12.70 / 0+1/2 / 0
> 3048 – 6096 mm> 10 – 20 ft	+15.88 / 0+5/8 / 0

Strip under 0.25 mm (0.010 in) thick: ±10 % up to 406 mm (16 in) wide, ±15 % from 406 to 608 mm (16 – 23 15/16 in). Strip thickness is measured 9.5 mm (⅜ in) from the edge; under 25.4 mm (1 in) wide, anywhere.
Cold-rolled sheet (under 4.76 mm thick): width +1.60 mm (1/16 in) from 610 to under 1220 mm (24 – 48 in), +3.20 mm (⅛ in) at 1220 mm and over; length +6.35 mm (¼ in) up to 3 m (10 ft), +12.7 mm (½ in) from 3 to 6 m (10 – 20 ft); no minus tolerance.
Hot-rolled sheet: width +15.88 – 20.64 mm (⅝ – 13/16 in) and length +19.05 – 38.10 mm (¾ – 1½ in) by length and width, no minus tolerance; flatness 19.05 – 57.15 mm (¾ – 2¼ in) by width or length.
Weight: a single item of cold-rolled sheet may exceed the estimated weight by 10 % (five sheets or fewer, or up to 91 kg / 200 lb) or 7½ % (larger items); hot-rolled sheet by 20 %; strip by 10 %. There is no minus weight tolerance; the minus thickness tolerance governs.

For copper-nickel and zirconium sheet and strip, tolerances are confirmed on enquiry.

Manufacturing and inspection

Cold-rolled, then solution-annealed and pickled, or annealed in a protective atmosphere for a bright finish.
Supplied in the temper ordered: annealed, or with a specified degree of cold work.
Every lot is checked by PMI to confirm the alloy.
EN 10204 3.1 certificates with every delivery; 3.2 with third-party witnessing on request.

Need a quote?

Send your specification, drawing or material list as it is; a grade and size are enough to start, and we confirm the rest in our reply. · info@kochlin.com

Submit RFQ

Other products

Tube & pipeSeamless and welded; heat-exchanger, instrument and U-bend tubePlateHot- and cold-rolled; sheared, waterjet-cut or cut to drawingBarRound, square, hexagon and flat; turned or groundForgingsRings, discs and shafts to drawingWire & filler metalsFine, spring and heating wire; nickel and titanium filler wirePipe fittings & flangesFlanges, elbows, tees, reducers, caps and stub ends

Corrosion-resistant alloy strip and sheet

Supply range

Types

Thickness, width and length tolerances

Manufacturing and inspection

Other products